@echo off
:: 判斷一個腳本執行完畢所需要的時間
:: 先取開始時間，然后在即將結束的時候取結束時間
:: 兩個時間都分別提取小時、分和秒數
:: 分別對小時數、分鐘數和秒數進行操作
:: 還要對08和09這兩個數進行操作
:: 注意：set /a num=的格式只能處理兩位數中是否高位為0，如果是多位數
:: 要去高位的所有0的話，要用循環測試高位是否為0或者在高位添1然后
:: 再減去1000之類的數字的方法
:: code by JM 2006-9-5～10 CMD@XP 感謝pengfei測試
set time_begin=%time:~0,-3%
echo 腳本開始運行時間是 %time_begin%
:: 小于10的小時數前有空格，要做去空格操作
for /f "tokens=1,2,3 delims=:" %%i in ("%time_begin%") do (
set /a hour_b=%%i
set /a munite_b=%%j
set /a second_b=%%k
)
pause
set time_end=%time:~0,-3%
for /f "tokens=1,2,3 delims=:" %%i in ("%time_end%") do (
set /a hour_e=%%i
set /a munite_e=%%j
set /a second_e=%%k
)
call :time_lapse
echo 腳本結束運行的時間是 %time_end%
echo 共花費了 %hour_% 小時 %munite_% 分 %second_% 秒
pause>nul
goto :eof
:time_lapse
:: 一定要按照 秒=>分鐘=>小時 的順序操作
if %second_e% lss %second_b% (
set /a munite_e=%munite_e%-1
set /a second_e=%second_e%+60
)
set /a second_=%second_e%-%second_b%
if %munite_e% lss %munite_b% (
set /a hour_e=%hour_e%-1
set /a munite_e=%munite_e%+60
)
set /a munite_=%munite_e%-%munite_b%
if %hour_e% lss %hour_b% (
set /a hour_e=%hour_e%+24
)
set /a hour_=%hour_e%-%hour_b%
goto :eof
另外一種方法(Code by Pengfei)：
@echo off
::11:08:25.45
:: 運行程序的時間統計
set _time_start=%time%
set /a hour_start=%_time_start:~0,2%
set /a minute_start=1%_time_start:~3,2%-100
set /a second_start=1%_time_start:~6,2%-100
echo %time%
echo %hour_start%
echo %minute_start%
echo %second_start%
pause
:: 結束程序的時間統計
set _time_end=%time%
set /a hour_end=%_time_end:~0,2%
set /a minute_end=1%_time_end:~3,2%-100
set /a second_end=1%_time_end:~6,2%-100
echo %time%
echo %hour_end%
echo %minute_end%
echo %second_end%
pause
:: 計算秒數
if %second_end% lss %second_start% (
set /a second_end=%second_end%+60
set /a minute_end=%minute_end%-1
)
set /a second=%second_end%-%second_start%
:: 計算分鐘數
if %minute_end% lss %minute_start% (
set /a minute_end=%minute_end%+60
set /a hour_end=%hour_end%-1
)
set /a minute=%minute_end%-%minute_start%
:: 計算小時數
if %hour_end% lss %hour_start% (
set /a hour_end=%hour_end%+24
)
set /a hour=%hour_end%-%hour_start%
echo %hour%:%minute%:%second%
pause