思科BGP AS-PATH配置實驗案例

本文實例講述了思科BGP AS-PATH配置。分享給大家供大家參考,具體如下:
Cisco BGP AS-PATH配置實例如下圖示:
R1:
interface Loopback0
ip address 1.1.1.1 255.255.255.255
interface FastEthernet0/0
ip address 12.1.1.1 255.255.255.0
interface FastEthernet0/1
ip address 14.1.1.1 255.255.255.0
router eigrp 1
network 1.1.1.1 0.0.0.0
network 12.1.1.0 0.0.0.255
network 14.1.1.0 0.0.0.255
no auto-summary
router bgp 100
bgp router-id 1.1.1.1
bgp log-neighbor-changes
no synchronization
neighbor 2.2.2.2 remote-as 100
neighbor 2.2.2.2 update-source Loopback0
neighbor 2.2.2.2 next-hop-self
neighbor 3.3.3.3 remote-as 100
neighbor 3.3.3.3 update-source Loopback0
neighbor 3.3.3.3 next-hop-self
neighbor 4.4.4.4 remote-as 200
neighbor 4.4.4.4 ebgp-multihop 255
neighbor 4.4.4.4 update-source Loopback0
neighbor 4.4.4.4 next-hop-self
no auto-summary
R2:
interface Loopback0
ip address 2.2.2.2 255.255.255.255
interface FastEthernet0/0
ip address 12.1.1.2 255.255.255.0
interface FastEthernet0/1
ip address 23.1.1.2 255.255.255.0
router eigrp 1
network 2.2.2.2 0.0.0.0
network 12.1.1.0 0.0.0.255
network 23.1.1.0 0.0.0.255
no auto-summary
router bgp 100
no synchronization
bgp router-id 2.2.2.2
bgp log-neighbor-changes
neighbor 1.1.1.1 remote-as 100
neighbor 1.1.1.1 update-source Loopback0
neighbor 1.1.1.1 next-hop-self
neighbor 3.3.3.3 remote-as 100
neighbor 3.3.3.3 update-source Loopback0
neighbor 3.3.3.3 next-hop-self
no auto-summary
R3:
interface Loopback0
ip address 3.3.3.3 255.255.255.255
interface FastEthernet0/0
ip address 34.1.1.3 255.255.255.0
interface FastEthernet0/1
ip address 23.1.1.3 255.255.255.0
router eigrp 1
network 3.3.3.3 0.0.0.0
network 23.1.1.0 0.0.0.255
network 34.1.1.0 0.0.0.255
no auto-summary
router bgp 100
no synchronization
bgp router-id 3.3.3.3
bgp log-neighbor-changes
neighbor 1.1.1.1 remote-as 100
neighbor 1.1.1.1 update-source Loopback0
neighbor 1.1.1.1 next-hop-self
neighbor 2.2.2.2 remote-as 100
neighbor 2.2.2.2 update-source Loopback0
neighbor 2.2.2.2 next-hop-self
neighbor 4.4.4.4 remote-as 200
neighbor 4.4.4.4 ebgp-multihop 255
neighbor 4.4.4.4 update-source Loopback0
neighbor 4.4.4.4 next-hop-self
no auto-summary
R4:
interface Loopback0
ip address 4.4.4.4 255.255.255.255
interface FastEthernet0/0
ip address 34.1.1.4 255.255.255.0
interface FastEthernet0/1
ip address 14.1.1.4 255.255.255.0
router eigrp 1
network 4.4.4.4 0.0.0.0
network 14.1.1.0 0.0.0.255
network 34.1.1.0 0.0.0.255
no auto-summary
ip prefix-list 1 seq 5 permit 4.4.4.4/32
route-map as_path permit 10
match ip address prefix-list 1
set as-path prepend 600 700
router bgp 200
no synchronization
bgp log-neighbor-changes
neighbor 1.1.1.1 remote-as 100
neighbor 1.1.1.1 ebgp-multihop 255
neighbor 1.1.1.1 update-source Loopback0
neighbor 1.1.1.1 next-hop-self
neighbor 3.3.3.3 remote-as 100
neighbor 3.3.3.3 ebgp-multihop 255
neighbor 3.3.3.3 update-source Loopback0
neighbor 3.3.3.3 next-hop-self
neighbor 3.3.3.3 route-map as_path out
no auto-summary
R4(config-router)#do ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/36/40 ms
R4(config-router)#do traceroute 1.1.1.1Type escape sequence to abort.
Tracing the route to 1.1.1.11 34.1.1.3 8 msec 12 msec 24 msec
2 23.1.1.2 32 msec 36 msec 44 msec
3 12.1.1.1 32 msec 44 msec 32 msec
R4(config-router)#
R4(config-router)#do show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static routeGateway of last resort is not set
34.0.0.0/24 is subnetted, 1 subnets
C 34.1.1.0 is directly connected, FastEthernet0/0
1.0.0.0/32 is subnetted, 1 subnets
D 1.1.1.1 [90/460800] via 34.1.1.3, 00:05:23, FastEthernet0/0
2.0.0.0/32 is subnetted, 1 subnets
D 2.2.2.2 [90/435200] via 34.1.1.3, 00:03:07, FastEthernet0/0
3.0.0.0/32 is subnetted, 1 subnets
D 3.3.3.3 [90/409600] via 34.1.1.3, 00:05:25, FastEthernet0/0
4.0.0.0/32 is subnetted, 1 subnets
C 4.4.4.4 is directly connected, Loopback0
23.0.0.0/24 is subnetted, 1 subnets
D 23.1.1.0 [90/307200] via 34.1.1.3, 00:05:36, FastEthernet0/0
12.0.0.0/24 is subnetted, 1 subnets
D 12.1.1.0 [90/332800] via 34.1.1.3, 00:03:10, FastEthernet0/0
14.0.0.0/24 is subnetted, 1 subnets
D 14.1.1.0 [90/358400] via 34.1.1.3, 00:05:37, FastEthernet0/0
相關文章
- 這篇文章主要介紹了思科Cisco BGP常用show命令,總結整理了思科Cisco BGP使用show命令查看BGP路由表與網絡狀態相關操作技巧,需要的朋友可以參考下2020-04-05
BGP邊界網關路由協議學習筆記之屬性和選路規則詳解
這篇文章主要介紹了BGP邊界網關路由協議學習筆記之屬性和選路規則,詳細分析了BGP屬性、路由條件及相關配置命令使用技巧,需要的朋友可以參考下2020-04-08BGP邊界網關路由協議學習筆記(二)路由聚合操作匯總
這篇文章主要介紹了BGP邊界網關路由協議路由聚合操作,匯總整理了BGP邊界網關路由協議路由聚合相關概念、原理、操作命令與使用注意事項,需要的朋友可以參考下2020-04-07BGP邊界網關路由協議學習筆記(一)
這篇文章主要介紹了BGP邊界網關路由協議,總結整理了BGP邊界網關路由協議的相關概念、原理、配置命令及操作注意事項,需要的朋友可以參考下2020-04-07最常用路由協議RIP-1/2 OSPF IS-IS BGP的特點對比
RIP協議是最早的路由協議,OSPF是目前應用最廣泛的IGP協議,IS-IS是另外一種鏈路狀態型的路由協議,BGP協議是唯一的EGP協議,那么這幾種路由協議有什么特點和不同呢?下面就2017-04-06理解BGP協議同步規則的目的和需求 中文PDF版
在bgp同步打開的情況下,一個BGP路由器不會把那些通過ibgp鄰居學到的bgp路由通告給自己的ebgp鄰居;除非自己的igb路由表中存在這些路由,才可以向ebgp路由器通告;有需要的朋2016-10-16邊緣網關協議(BGP)報頭結構詳解 中文PDF版
路由包括兩個基本的動作:確定最佳路徑和信息群(通常稱為分組)通過網絡的傳輸。通過網絡傳輸分組相對較簡單, 而路徑的確定可以分復雜。 BGP 就是當今網絡中實現路徑選擇2016-10-16- BGP作為一種廣泛使用的邊界網關路由協議,從設計上提供了強大的路由過濾能力,與一般的訪問列表ACL不同的是,基于BGP屬性的路由過濾是通過對路由屬性的控制或修改來完成的2016-10-16
- 這篇文章主要為大家介紹了邊界網關協議BGP的概念,怎么配置BGP?下面文章里有詳細的BGP基本配置的方法步驟,有興趣的可以和腳本之家的小編一起來看一下2014-09-24
- BGP協議是運行在TCP之上的,所以TCP的參數設置會影響B(tài)GP的性能。在路由數目比較少的情況下TCP的參數調整可能對BGP性能影響不大,但是當路由數目比較巨大的時候調整TCP參數2012-11-19